AB Dick 9870

Since: Apr 12

Portland, OR

#108 Jul 23, 2012
There are often problems with the LED display on this particular machine. I had the same issue among others upon purchasing this model. That is most likely the culprit. It's not too expensive to replace.
Lori

Rochester, NY

#109 Oct 19, 2012
phenix wrote:
<quoted text>
Do you have operator manual for ab dick 9870? can you email me if you do?
admin@phenixprint.com
Thanks.
If you have the wiring manual could you please email it me as well. lori@pressmarc.com.
we are having trouble with the emergency switch.
Lori

Rochester, NY

#110 Oct 19, 2012
Timmycan wrote:
<quoted text>
Most likely the "flag" part # 009536 to the input or feed-in sensor is worn. If heavier stocks feed fine with no going on / off impression, this is likely the problem. very easy to fix .
I was wondering if you had the electrical manual for the ab dick 9870 press. if you do could you please email lori@pressmarc.com
Brendon

Salem, NJ

#112 Dec 14, 2012
i have a 9870 problem is whenever i press the feed button i get a CLEAR OUTPUT JAM code but there is nothing jammed in there can anyone help?
Bob Powell

Newark, NJ

#113 Dec 21, 2012
My 9870 will not run...When I press the drive button, it jumps a little and does not run. I checked the input voltage on the speed control board and have no voltage reading. I changed the motor and a few other parts after water damage. Need help ASAP.
Brendon

Salem, NJ

#114 Jan 3, 2013
Your keypad is messed up i have same problem lift keypad and place a small piece of tape or paper under the drive button you might have to keep djusting paper untill machine works
jim

San Benito, TX

#115 Feb 19, 2013
anyone know how to change the led readout to english from german jwarmey@yahoo.com
Pam

Valley Park, MO

#117 Jun 12, 2013
I have a 9800 and it runs for a short time and then stops with emergency switch trouble message. Can anyone tell me how to fix this?
ashish

Jalgaon, India

#118 Jul 5, 2013
i have abdick 9870.. which is showing clear double plz let me know what to do for this...
Shawn

Albany, KY

#119 Jul 22, 2013
I have a 9870 that runs for a short time before the emergency switch trouble message appears. Any ideas how to fix this?
Shawn

Albany, KY

#120 Jul 22, 2013
Pam wrote:
I have a 9800 and it runs for a short time and then stops with emergency switch trouble message. Can anyone tell me how to fix this?
Pam- I am having the same issue, did you find a solution?
SCruz

Saint Petersburg, FL

#121 Aug 13, 2013
I have a abdick 9910 and recently started having trouble with the clutch spring breaking after only a few days. the press also makes a rattling sound every time i turn it on. Any advice would be great.
Guy

Tucson, AZ

#122 Sep 16, 2013
Shawn wrote:
<quoted text>
Pam- I am having the same issue, did you find a solution?
How short a time? 3 revolutions?
Angie

Saint Charles, MO

#124 Oct 19, 2013
I have a ABDick 9800 (Dahlgren) having a problem with fountain, it is scumming on non operator side
and I cannot find a manual anywhere help before I throw this dang think in the river
butch

Paducah, KY

#126 Mar 5, 2014
model 9870 1993 dc motor will not run sounds like it is trying to. It is a friends machine sounds like drive board. But I have no wiring diagrams no manuals to check it with any ideas
Keifer

Castries, Saint Lucia

#128 Jun 17, 2014
I have an AB Dick 9870 and it will feed one sheet And jams on the second sheet saying "clear output jam. The feed sensor has been removed cleaned and replaced but the problem still is same. Please help . Thanks

Since: Nov 13

Auburn, CA

#129 Aug 29, 2014
Keifer wrote:
I have an AB Dick 9870 and it will feed one sheet And jams on the second sheet saying "clear output jam. The feed sensor has been removed cleaned and replaced but the problem still is same. Please help . Thanks
There's a sensor on the delivery end make sure you clean out the dust, it reflects bottom to the top
Rich

Mullica Hill, NJ

#132 Feb 26, 2015
My feed table only raises when the side lever is in the highest position, then it won't stop when it gets to the top. Hate to call service Does anyone have any answers or thoughts ?
Rich

Mullica Hill, NJ

#133 Feb 26, 2015
I forgot to say it is an 8820 AB Dick with on electronics sensors on it.
Mike

Gulfport, MS

#134 Mar 27, 2015
Joe wrote:
I just bought a used AB Dick 9870 and the ink leaks from the fountain. It appears the fountain is too big. Any ideas how to fix this problem?
there are rubber seals on each end of the ink fountain that needs to be replace,, easy to do

Tell me when this thread is updated:

Subscribe Now Add to my Tracker

Add your comments below

Characters left: 4000

Please note by submitting this form you acknowledge that you have read the Terms of Service and the comment you are posting is in compliance with such terms. Be polite. Inappropriate posts may be removed by the moderator. Send us your feedback.

Commercial Printing Discussions

Title Updated Last By Comments
KPI's Jan 18 Nova Scotia 1
catalog/magazine printing Jan 9 RepFitness 1
Im Looking for graphic designer for Coupon Maga... (Aug '07) Dec '17 Hometown Values ... 38
Digitial printing options? Dec '17 kev_24 2
Discotheque - Trip the Light Fantastic - Mind C... Dec '17 kev_24 2
New age banner printing, (Jun '11) Dec '17 kev_24 16
Multi 1250 printing press Dec '17 kev_24 2
More from around the web