ford explorer keypad code location

[joe]

Would anyone have any information regarding the location of the keypad code number for the keyless entry for a 1997 Explorer?

[Steve]

On a 99' Ford Explorer XLT the code is in the trunk of the truck behind the plastic cover where your tire jack and wrench are!!!!! There will be two plastic knobs that you will have to turn to open and lift it off, real simple. The code will be on the fender wall, bring paper and pen to write and will need a flash light so you can see the code clearly!!! The code is real close the the plasic and kinda hard to see. Hope this helps!!!!!!
If you dont see the above,then try looking around in that area for a 5 digit code, in the fender well or around the jack, or even around the rear washer bottle. Most people have said its around the jack.

[gael]

Would anyone have any information regarding the location of the keypad code number for the keyless entry for a 2002 Explorer?

[W AUSTIN]

gael wrote:

Would anyone have any information regarding the location of the keypad code number for the keyless entry for a 2002 Explorer?

BEHIND DRIVER DOOR PANEL OR RIGHT SIDE REAR TRIM PANEL LOOK AT PASS SIDE REAR DOOR OPENING AND PULL REAR TRIM OUT THERE

[Steve]

2002 Explorer....Try reading posts: http://www.topix.net/forum/autos/ford-explore...

[jed]

jed?

[ALLAN C]

WHERE CAN I FIND THE DOOR CODE ON MY 2000 FORD EXPLORER JUST BOUGHT IT AND LOCKED MYSELF OUT....LOL

[Steve]

ALLAN C wrote:

WHERE CAN I FIND THE DOOR CODE ON MY 2000 FORD EXPLORER JUST BOUGHT IT AND LOCKED MYSELF OUT....LOL

Try the link above...Also, the code will be located "Inside" the car..sorry..LOL

[Casey]

I own a 1998 Ford Explorer Sport. I have the keypad entry but I dont know the code. Can anyone tell where to find it inside the truck. I've looked everywhere. Please help!!!

[Keypad]

There is another guy who has the location on a word document and good pictures that sells it for 10.00

his ebay id is: ssshr

[leo hilliard Ireland]

Hi guys,does any one know how to progam a new remote for my explorer ,1999.

[Jake]

Is there a way to change to factory set code for the 99 explorer

[Scott R]

Jake wrote:

Is there a way to change to factory set code for the 99 explorer

.
.
.
NO, you cannot change the factory set code but you can add your personal code by doing the following
1. Enter the factory-set code (keypad will illuminate when pressed).
2. Press the 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of the previous one.

[Scott R]

leo hilliard Ireland wrote:

Hi guys,does any one know how to progam a new remote for my explorer ,1999.

To reprogram the transmitters
yourself, place the key in the
ignition and turn from OFF to ON
eight times in rapid succession
(within 10 seconds) ending in ON. After doors lock/unlock, press any
control on all transmitters (up to four). When completed, turn the
ignition to OFF. The doors will lock/unlock one last time to confirm
completion of program mode.
All transmitters must be programmed at the same time.

[Scott R]

Casey wrote:

I own a 1998 Ford Explorer Sport. I have the keypad entry but I dont know the code. Can anyone tell where to find it inside the truck. I've looked everywhere. Please help!!!

if you look in the cargo area of your truck and in the jack compartment (in the cargo area driver's side) Look all the way back on the wheel well.. you'll see a white sticker with 5 bold numbers on it.. that's your code.. also.. a flashlight might be a good idea.

[Sean]

1996 Eddie Bauer Explorer

I looked on the computer module and also in the cargo area (jack compartment) for the keypad entry number and still can't find it. Can someone help me locate it?

[Rick Thomas]

Does anyone know how I can disable the door keypad to my 2000 Ford Explorer but still be able to use the remotes?

[lenny]

i got a 1995 ford explorer limited an i am trying to find the code for the key pad but i canot fin it in the book talk about a computer module were is that blocated

[LaJuan]

Scott R wrote:

<quoted text>.Will this work to add my own code to the 2000 XLT Explorer? I have the factory code but, don't know how to add my own to the keyless entry.
.
.
NO, you cannot change the factory set code but you can add your personal code by doing the following
1. Enter the factory-set code (keypad will illuminate when pressed).
2. Press the 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of the previous one.

.Will this work to add my own code to the 2000 XLT Explorer? I have the factory code but, don't know how to add my own to the keyless entry.

[LaJuan]

Is there a way to add my own code to the keyless entry of a 2000 XLT 4x4 Explorer? I have the factory code and want to add my own code. Can somebody please email at: [e-mail]

Thanks,

LaJuan